How To Upgrade Your Miller Diversion Welding Machine

Looking to upgrade your current Miller Diversion welding machine? Check out our top of the line JWS TIG Torch Upgrade Kit!

Add a water-cooled TIG torch to your Miller Diversion welding machine

Air or Water-Cooled TIG Torch: Have it Your Way!

Add a water-cooled TIG torch to your Miller Diversion welding machineAt Arc-Zone we’re all about improving your welding performance. Our team of skilled technicians has been working hard on developing a line of innovative Welding Machine Upgrade kits—the JW Signature Series (JWS Series) of welding solutions.

The JWS TIG Torch Upgrade kit for the Miller Diversion® power supplies is a basic upgrade kit that allows you to switch out your factory-installed WP-17 (A-150) series 12.5 (3.8m), a general-purpose TIG torch, for a more modern 12.5’ (3.8m), 25’ (7.6m) or 50’ (15.2m) torch in a rigid or flexible head design.

You can greatly improve your welding versatility with the Air-Cooled Upgrade Kit, but when you’re ready to amp up your TIG welding even more you’ll want to get the JWS Air/Water-Cooled TIG Torch Upgrade Kit.

Water Cooled Upgrade Kit for Miller Diversion

With the Air/Water-Cooled Upgrade Kit not only will you improve your machine’s performance even more, you’ll improve your ability to do a wider variety of welding jobs, and have the ability to accessorize your torch and work lead to achieve high-quality TIG welding on a variety of material types and thicknesses. 

When you’re ready to go to the next level and add air and water-cooled TIG Torches to your tool kit, the JWS Air/Water-Cooled TIG Torch Upgrade Kit is for you!
Kit Includes:

  • 1ea. Black Female Panel Mount Power DINSE Receptacle
  • 1ea. Red Female Panel Mount Work Lead DINSE Receptacle
  • 1ea. Red Male Work Lead DINSE Connector
  • All Related Hardware to Complete Your Miller Diversion Upgrade

The JWS Air/Water-Cooled TIG Torch Upgrade Kit is affordable and easy to install in just a few steps:

Installation Instructions: 

  1. Turn Off Machine’s Power Switch and UNPLUG THE POWER CORD!
  2. Remove the machine cover, factory-installed TIG Torch, and work lead connector and strain relief(s). Save the covered Work Lead cable with Eyelet Connector.
  3. Cut the covered Work Lead (opposite the Eyelet Connector) so you have 12″ of work lead cable. This will be your new Internal Work Lead connection to the (red) Panel Connector.
  4. Strip the end of the covered Work Lead (opposite end of the Eyelet Connector) and connect the Arc-Zone supplied 45 degree angle connector.
  5. Drill the two existing holes in the machine’s front panel to 30mm (1-3/16″) (TIG torch/Work Lead connections) using the Arc-Zone supplied Bore Drill
  6. The 30mm hole must have a 1/4″ x 1/4″ inch keyway cut into the enlarged holes to nest the New Panel Receptacles. This can be done with a hand file. If you do not perform steps 5 & 6, you could have the Welding current in direct contact with the machines chassis.
  7. Disassemble the Black and Red panel Mount Receptacles and insure that they fit into the holes on the machine’s front panel.
  8. Install TIG torch panel mount connector, (Black) into Upper Hole in machine face, with flat and lock washer so as to sandwich the machine’s power eyelet. Tighten as needed.
  9. Install Work Lead panel mount connector, (Red) into Lower Hole in machine face. Tighten as needed.
  10. Tighten the Work Lead eyelet connectors to the motherboard and the Lower (Red) Panel Connector.
  11. Verify that all connections are tight and Re-install the machine cover.

Complete Your Upgrade

Complete your upgrade with a new high-performance TIG torch! Select the torch and amperage that best fits your application.  Arc-Zone recommends having a “daily use” and a “micro” or “low-profile” TIG  torch for those hard-to-reach areas.  With two torch models, you’re covered for any job that comes through the shop door!

CK Micro TIG Torch Models:

CK-MR70 – Micro, 70 amp Air-cooled

CK-80 – Low-profile, 80 amp Air-cooled

CK-MR140 – Micro, 140 amp Water-cooled

CK-180 – Low-profile, 180 amp Water-cooled

CK General Purpose Rigid Torch Models:

CK-130 – Compact, 130 amp Air-cooled

CK-150 – Robust, 150 amp Air-cooled

CK-200 – Compact, 250 amp Water-cooled

CK General Purpose Flex-Neck Torch Models:

CK-130 FX – Compact, 130 amp Air-cooled

CK-150 FX – Robust, 150 amp Air-cooled

CK-200 – Compact, 250 amp Water-cooled

CK Flex-Loc Articulating Head Torch Models:

CK-FL130 & CK-FL150 – Flex-Loc Air-Cooled

CK-FL230 & CK-FL250 Flex-Loc Water-cooled


Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.